1、合理的放置开云网页登录

1. Reasonable placement of military models

关于不要置于高处，以免意外掉落造成损失。不要置于儿童容易接触到的地方，以免给双方(小朋友和小车车)都造成伤害。这些属于避免意外发生的小提醒，各家庭的条件不同，大家肯定自有分寸。

Do not put it at a high place, so as to avoid the loss caused by accidental drop. Do not put it in a place easily accessible to children, so as to avoid injury to both parties (children and car). These are small reminders to avoid accidents. The conditions of different families are different, so we must have our own discretion.

开云网页登录 忌高温。所以开云网页登录 不要长期暴露在阳光[综述 图片 论坛]直射之下，同理也不要使用传统的小射灯长期进行照射。传统碗状小射灯的温度是很高的，对开云网页登录 漆面的伤害较大。其实作为普通开云网页登录 爱好者，是完全没有必要去专门搞一个灯光源来做博物馆式的展示的，把玩时如果想看灯光效果，台灯就足以。当然，对于藏品众多，经济条件允许，有专门陈列展柜的藏家，希望置备灯光效果时，可以考虑一下灯，功率小、温度相对低。同时，在展柜内放置一小杯水，有利于缓解干燥和静电效应。

High temperature is not allowed in military models. Therefore, military models should not be exposed to direct sunlight for a long time, nor should they be exposed to traditional small spotlights for a long time. The temperature of traditional small bowl spotlight is very high, which damages the surface of military model. In fact, as ordinary military model enthusiasts, there is no need to create a light source to do Museum style display. If you want to see the lighting effect, the desk lamp is enough. Of course, for collectors who have a large collection and economic conditions allow, when they want to purchase lighting effects, they can consider energy-saving lamps, which have low power and relatively low temperature. At the same time, a small cup of water is placed in the display cabinet to ease the drying and electrostatic effects.

开云网页登录 忌过湿。湿度过大，漆面容易发生氧化反映，出现黑点、甚起泡。大原则是将开云网页登录 放置于通风干燥的地方。对于一些空间不足的藏家有时需要将开云网页登录 放回原包装内，置于角落等处。这就需要注意，所放的位置是否湿度过大了。在包装内放一些干燥剂会有所帮助，有些开云网页登录 产品的包装内本身就带有干燥剂包；如果没有的话，一些食品包装内的干燥剂应该也可以啦：)。

The military model should not be too wet. If the humidity is too high, the paint surface is prone to oxidation reaction, black spots and even blistering. The general principle is to place military models in ventilated and dry places. For some collectors with insufficient space, sometimes they need to put the military model back into the original package and put it in the corner. This requires attention to whether the humidity is too high. It is helpful to put some desiccant in the package. Some military model products have desiccant package in the package itself. If not, the desiccant in some food packaging can also be used:).

这么看来，上面说的两点岂不是矛盾了吗？所以说，还是要根据实际情况来分析决定的。大家所处城市的自然环境的区别就很巨大，比如北京和广州在温度湿度上都会有比较大的区别。避免极端情况就好，用不着太拘泥于某种规范要求。

So, are the above two points contradictory? Therefore, it is still necessary to analyze and decide on the basis of the actual situation. The difference between the natural environment of the city you live in is very big. For example, Beijing and Guangzhou have big differences in temperature and humidity. It's good to avoid extremes and not to be too rigid about certain specifications.

悬空放置。长期放置的开云网页登录 ，需要将底盘垫高，以避免四轮长期受到车身的压力，而造成轮轴变形、轮胎八字。关于这一点，我个人的看法，似乎并没有那么严重。少我的一台1：18的KYOSHO宝马6系[综述 图片 论坛]放了四年了，也没有变成八字脚啊。不同制造商、不同比例、不同款式的开云网页登录 ，重量也不尽相同，可能对于某些自重很大的产品，这一点需要注意吧。毕竟轮轴等构件的材质基本相同，可以承受的压力范围是有限的。

Suspended. For a military model placed for a long time, the chassis needs to be padded up to avoid the wheel axle deformation and tire splayed under the pressure of the vehicle body for a long time. My personal opinion on this point seems not so serious. At least one of my 1:18 kyosho BMW 6 series [overview photo Forum] has been in use for four years, and it has not become a zigzag foot. Different manufacturers, different proportions and different styles of military models have different weights. Maybe for some products with high self weight, we need to pay attention to this. After all, the materials of wheel axles and other components are basically the same, and the pressure range they can bear is limited.

经常更换轮胎着地点。长期放置的开云网页登录 好可以经常转动转动车轮，以变换车轮的着地点。这样一是可以避免车轮变成鸭蛋圆(这种情况出现的几率恐怕也不是很高)；二是可以避免轮胎着地点发生粘连，这个到是需要注意，尤其温度较高的情况下。

Change the landing point of tires frequently. It is better for a long-term military model to rotate the wheel frequently to change the landing position of the wheel. One is to avoid the wheel turning into a duck's egg circle (I'm afraid the probability of this situation is not very high); the other is to avoid tire adhesion at the landing site, which needs attention, especially in the case of high temperature.

开云网页登录 要注意防尘。作为微缩的汽车，机构比较复杂，如果积了比较多的尘土，清理起来还是比较麻烦的。好不要直接暴露的长期置于桌面、多宝阁之类的地方。有条件的话，带玻璃门的书柜、储物柜是比较好的选择。如果只是自己欣赏把玩，平时也可以用布适当的进行遮盖。于专用的一次成型的展盒，单价不便宜而且还不是很容易买到；而自己去定做有机玻璃粘合的展盒的话，不见得可以节省，粘合处恐怕也不会好看。

Military models should be dustproof. As a miniature car, the mechanism is more complex. If there is more dust, it is still more troublesome to clean up. It is better not to directly expose the long-term desktop, Duobao Pavilion and other places. If possible, bookcase with glass door, locker is a better choice. If you just enjoy playing, you can also cover it with cloth properly. As for the special one-time forming exhibition box, the unit price is not cheap, and it is not easy to buy; and if you customize the exhibition box of plexiglass bonding, you may not be able to save much money, and the bonding part will not look good.

本文由大型坦克模型整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：//www.leshep.com我们会有更多精彩内容等你查看。

This article is organized and released by large tank models. Do you have any understanding of these contents? For more information, please click: //www.leshep.com We'll have a lot more to see.