今天
大型机器人模型制作厂家要给大家讲解一下有关于机器人模型制作的过程的知识点，希望通过我们的讲解能够更好的帮助到大家了解到这方面的知识点。
Today, the large-scale robot model manufacturer will explain to you some knowledge points about the process of robot model production. We hope that our explanation can better help you understand this knowledge point.
一、根据客户要求及场地特点设计机器人模型效果
1、 Design robot model effect according to customer requirements and site characteristics
二、确定材质，进行小稿制作。
2、 Determine the material and make small drafts.
三、造型师按所需比例进行放大，制作骨架并对骨架（按雕塑、高度等数据）进行加固、防腐、防锈处理。
3、 The stylist shall enlarge the scale as required, make the skeleton and carry out reinforcement, anti-corrosion and anti rust treatment on the skeleton (according to the center of gravity, height and other data of the sculpture).
四、对钢板进行整体剪裁。
4、 Cut the steel plate as a whole.
五、亚弧焊焊接，锻打，力求做到无明显焊缝、线条流畅、表面平整。
5、 Sub arc welding and forging shall strive to ensure no obvious weld, smooth lines and smooth surface.
六、对机器人模型进行抛光使纹理自然。
6、 Polishing the robot model to make the texture natural.
七、包装车间根据模型大小进行分解包装。
7、 The packaging workshop decomposes the packaging according to the model size.
八、大型机器人模型工艺流程图
8、 Process flow diagram of large robot model
九、运输到施工场地后进行整体合并和相应的后期处理。
9、 After being transported to the construction site, the overall consolidation and corresponding post-treatment shall be carried out.
机器人模型制作维修注意：
Robot model making and Maintenance Notes:
将机器人模型制作表皮小面积破坏的位置用针线缝合,然后用硅酮胶均匀涂抹在缝合处,防止机器人模型制作进水,接下来再用丙烯颜料补色。
Sew the small-area damaged position of the robot model making skin with a needle and thread, and then apply silicone glue evenly on the suture to prevent water from entering the robot model making, and then use propylene pigment to supplement the color.
如果是机器人模型制作大面积的表皮损坏,需要先填充海绵,然后再用硅酮胶将纤维布粘附在上面,接下来再刷一层硅酮胶作为防水层,使用丙烯颜料稀释以后用空压机结合喷漆枪补色。
In case of large-area skin damage caused by robot model production, sponge shall be filled first, and then silicone adhesive shall be used to adhere the fiber cloth on it. Next, a layer of silicone adhesive shall be applied as a waterproof layer, and after being diluted with propylene pigment, air compressor and spray gun shall be used for color compensation.
在进行机器人模型制作维修时,-定要注意防火防热,在一些钢架断裂区域,需要使用焊接操作时,要将机器人模型制作表皮大面积剥开,避免焊接产生的火花或者热量将考虑海绵填充层引燃。
During the production and maintenance of robot models, attention must be paid to fire prevention and heat protection. In some steel frame fracture areas, when welding operation is required, the robot model production skin shall be peeled off in a large area to avoid sparks or heat generated by welding. The ignition of sponge filling layer shall be considered.
Sometimes when repairing the skin of the robot model, there will be water and dust on the surface. You should clean it before repairing. For more related matters, please visit our website //www.leshep.com Consult and understand.
