有许多类型的模型，其中常见的就是工业模型。认识的朋友都知道，工业模型制作，是打磨。磨料加工有很多地方需要注意，要讲究经验和技巧。装配模型时，模型表面会出现大量的裂缝，严重影响模型的外观，因此必须对模型缝隙进行修补，主要工具是填充、抹布和砂纸。
There are many types of models, the most common of which is the industrial model. Friends know that the first step in making industrial models is polishing. There are many places to pay attention to in abrasive machining. We should pay attention to experience and skills. When assembling the model, a large number of cracks will appear on the model surface, which will seriously affect the appearance of the model. Therefore, the model cracks must be repaired. The main tools are filling, rag and sandpaper.
另外，还应注意，工业模型在组合时必须粘结，否则接缝容易断裂。土又名有机树脂，专门用来填充模型间的空隙。也有许多类型适用于许多大的模型库。在使用时，用合适的工具在要填充的关节线或槽处施加适当的量。在施工过程中，施加一定的压力填充凹角。土体成分含有可溶解的塑料溶液，因此当它接触模型表面时很难脱落。但由于溶液会挥发，所以在完全干燥和硬化的时候，体积会稍微收缩。在补土的时候，我们必须补一点，使土壤有足够的体积，以满足磨削需要。
In addition, it should also be noted that the industrial model must be bonded during combination, otherwise the joint is easy to break. Soil, also known as organic resin, is specially used to fill the gaps between models. There are also many types that apply to many large model libraries. When in use, use a suitable tool to apply an appropriate amount at the joint line or groove to be filled. During construction, a certain pressure shall be applied to fill the concave corners. The soil component contains soluble plastic solution, so it is difficult to fall off when it contacts the surface of the model. However, due to the volatilization of the solution, the volume will shrink slightly when it is completely dried and hardened. When replenishing the soil, we must replenish a little to make the soil have enough volume to meet the grinding needs.
工业模型制作抛光后，你可以对它着色。你可以用你的手或者喷笔。手涂涂料的优点是能在某些精细区域使用，但大面积使用时容易产生笔痕。用喷枪在较大的区域内喷涂非常均匀。油层比较薄，起到的作用更好。但在小一点的地方使用分色纸比较麻烦。
After the industrial model is made and polished, you can color it. You can use your hand or fountain pen. The advantage of hand coating is that it can be used in some fine areas, but it is easy to produce pen marks when used in a large area. Spray evenly over a large area with a spray gun. The oil layer is relatively thin and plays a better role. But it is more troublesome to use color separation paper in smaller places.
工业模型不像手工模式那么简单，它已经从数码产品、家用医疗产品和汽车零部件转变为大型机械模式和工程模式。比建筑模型大得多，而且工艺难度因素也有进一步提高。
Industrial model is not as simple as manual model. It has changed from digital products, household medical products and auto parts to large-scale mechanical model and engineering model. It is much larger than the building model, and the process difficulty factors have been further improved.
1.尽量把工业模型放在通风干净的房间里，以免受潮和阳光直接照射。室温不超过35℃，相对湿度不超过30%-80%，否则易发生工业模型脱胶变形。工业模型不能直接暴露于阳光下，更不要说在阳光下暴晒。
1. Try to put the industrial model in a well ventilated room to avoid moisture and direct sunlight. The room temperature shall not exceed 35 ℃, and the relative humidity shall not exceed 30% - 80%, otherwise the degumming deformation of the industrial model is easy to occur. Industrial models cannot be directly exposed to the sun, let alone exposed to the sun.
2.工业模型宜看不宜接触，尤其在市场营销展示时，应采取相应措施。装饰物，绿树等小配件如有脱落，应妥善保管，并允许模型制造公司的维修人员及售后服务人员稍后再安装。
2. The industrial model should be seen rather than contacted, especially when displayed in the marketing center, corresponding measures should be taken. If small accessories such as decorations and green trees fall off, they shall be kept properly, and professional maintenance personnel and after-sales service personnel of the model manufacturing company are allowed to install them later.
3.灯光应每两小时关灯一次，不要长时间关灯。假如真有沙盘式喷泉，它应该经常检查有没有水(因为水在不断蒸发)。水不够用时应及时补充。如果发现喷泉不喷水，应立即关闭电源，以免造成损坏。
3. The light should be turned off every two hours, not for a long time. If there is a sand table fountain, it should always check whether there is water (because the water is evaporating). When the water is not enough, it shall be replenished in time. If it is found that the fountain does not spray water, turn off the power immediately to avoid damage.
以上就是小编为大家介绍的工业模型维护的全部内容，看完文章的你应该有所了解了。
The above is the whole content of industrial model maintenance introduced by Xiaobian. You should know something after reading the article.
The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: large tank model //www.leshep.com
